Recent content by BinaraA

Thanks for the reply. I read the other post as well. I'll try like that. Is there any danger of using this battery for flying?

I'm using a DJI Phantom 1 copter. I bought a new battery for it. When I plug it it to the charger(DJI original charger), it charges for few minutes and starting to blink both red and green lights of charger. I hope this is some kind of a error. And after that I didn't use that battery for...

When I opened my phantom, It doesn't have the upgraded board (I hope so). But it has the Naza V2 (yellow one). My phantom model number is P330D. So, how can I install n wire the Zenmuse gimbal and AVL58 FPV system. I have the GCU, do I need a PMU for this board. Can Anyone guide me? Here is a...

Thanks for the reply. I have the Phantom With Upgraded board. Could you please give me instructions, which cable to plug where? And what about the gimbal tilt control and DJI AVL58 video transmitter cables are going to plug? I've seen a one tutorial, which wires without GCU, is it possible...

I have a DJI phantom 1.1.1 copter (with NAZA M V2) . Please guys, give me instructions, how to wire DJI Zenmuse H3-2D Gimbal and DJI AVL58 video transmitter on my copter correctly ? there are various tutorials on internet, but most of them are to wire with Naza 1(the red color one). I need to...

Thanks gbshovel, for the comment. - What do you mean by "Have you had your TX apart for upgrade?" - No, the losing connection distance is random. sometimes it loses in very short distance. - I've already checked for the receiver antena cables. It looks fine. - I did this test, the copter is on...

I sent the copter back to singappore dealer of DJI Phantom, and they said there is a issue on this copter. Which is flashing yellow light continuously while flying and turns on the auto pilot system and automatically comes back home. They said they did a firmware update and now the issue is...

I've made a custom sized box for it and cut foam layers according to the shape of phantom copter, transmitter, batteries, charger, etc. The box dimensions are length- 30 inches, width-24 inches, height-14 inches. Its a this kind of a box, you can make it in custom sizes...

Thanks everybody for your helping hand. Finally, I couldn't sort out the loosing signal issue. It is continuously happening. So, I don't have any option, other than sending it back to a phantom dealer and fix this for us. I informed the about the problem. They suspect it might be a problem with...

Not all the way to ground, but a bit. Its not that much heavy. Just flying with GoPro and HiFly Gimbal.

I've got a loosing signal problem, in phantom copter. I've previously put a topic on phantom pilots forum, regarding this. As my Phantom dealer told me, the problem is with signal receiver(it has 2 antennas) of phantom copter. I don't have much time to send this back to my dealer (heliguy,UK)...

As I was told by the phantom dealer (Heliguy), the fault is with the signal receiver of the copter.Could anyone please tell me, can I buy a receiver and replace it in my own? because I don't have much time to send the phantom back to them n bring it back.

We have talked to the "Heliguy" (UK) also, where we bought the phantom from. They said it might be a fault with the receiver. That means, it has to be replaced. Then I'm going for the last option, that I have. I have to send this back to Heliguy(UK), to fix this problem. Thank you very much guys...

I checked for the GPS cable, inside phantom, they are not even look like loosen. And checked for the receiver type in assistant software, which is on the "D-Bus". Still has that problem. sometimes it looses signal, even within 10 meters. Then what may be the cause guys ? Plz help me, I'm stuck...

Please also tell me guys, what is the transmitter type, that I should select from the assistant software (traditional, D-Sub or PPM). may be accidantly I have selected the wrong type. Can this cause a loosing connection problem ?