A month ago, I had a shoot, took my Inspire 1 and two Phantom 3 Pro’s, finished the job and put the machines back in their perspective cabinet for storage. Three weeks later, I pull them back out for another gig take them out to run them up and guess what? The Inspire 1 and two of the Phantom 3’s Pro's now have the same exact problem;
“No Image Transmission”
For 3 weeks I have have tried every conceivable thing to remedy the problem but according to my hidden files (below) there is no communication on any of the 3 machines to the video transmit transmit board.
Everything else on the machines works perfect (except no image) it flies fine, Sats locks, IMU good, calibrates fine, etc.,etc. When I record video or stills, it records the data fine on the chip. When I stick the chip in my Mac, everything is normal good quality and clear playback. The second remote trans also works perfect.
This is just a "Few" of the different options I’ve tried:
Tried three different transmitters
Tried different locations
Changed 3 Batteries
Changed the micro chips
Re-installed the same firmware on machine
Install latest Firmware on machine
Re-Installed latest firmware on the transmitter
Re-installed the Go App
Tried 2 different iPad Mini’s
Try iPhone 6 +
Try a Samsung S7
Remove the camera and cleaned all the contacts
Try countless different combinations on the app i.e. 4K, 1080 decoding, etc.
I checked the hidden files on both the Inspire and P3P and it shows "Device Not Detected" on 08 00 & 15 00. which means the output boards are DOA.
[00006569]========== remo-con disconnect. boot(15) ============
[00006617]Packet [C:\WM610_FW_V01.10.01.40.bin] detected, card sn [0x07909b35].
[00006667]Packet upgrade start...
[00006715]Packet checking...
[00006772]Packet vlink 01.10.0140 <-> 01.09.0130.
[00006827]Record vlink 01.04.0010 <-> 01.03.0000 (flow = 0).
[00006882]Done.
[00006925]Version checking[1]...
[00006997][04 00][00] v1.30.1.43 -> v1.30.1.43
[00019567][08 00][00] device not detected.
[00019609][01 00][00] v2.70.5440 -> v2.70.5440
[00019654][01 01][00] v2.70.5440 -> v2.70.5440
[00019741][03 05][00] v34.1.0.5 -> v34.1.0.5
[00019819][03 06][00] v2.4.20.28 -> v2.4.20.28
[00019919][05 00][00] v3.0.6.2 -> v3.0.6.2
[00019995][09 00][00] v3.1.0.0 -> v3.1.0.0
[00020079][11 00][00] v3.9.0.0 -> v3.9.0.0
[00020167][12 00][00] v1.11.0.0 -> v1.11.0.0
[00020240][12 01][00] v1.11.0.0 -> v1.11.0.0
[00020319][12 02][00] v1.11.0.0 -> v1.11.0.0
[00020462][12 03][00] v1.11.0.0 -> v1.11.0.0
[00033007][15 00][00] device not detected.
[00033078][17 00][00] v1.1.0.8 -> v1.1.0.8
[00033180][17 01][00] v2.0.1.6 -> v2.0.1.6
[00033232][19 00][00] v1.0.8.96 -> v1.0.8.96
[00035277]Packet upgrade failed at version checking.
On the P3P - I ordered a replacement board for my P3P but the one DJI sent to me only has 2 antenna connections where mine as 4 connections. Would anyone have the correct info or board?
On the Inspire - I cannot find any information at all on the transmission board or its replacement.
It appears this No Image Transmission problem is very common and wide-spread. In the past month, I’ve found hundreds of posts with the same exact problem. I’m assuming the output board is running too hot and after a 6-12 months they all start failing.
I tried the DJI forum for 3 weeks now with absolutely no help or any solution, DJI is very aware of the problem but refuse to comment or assume any repair based on the fact they would have to replace thousands of boards and of course DJI does not have very much money (Only $10 Billion) to fix this problem.
Any help would be greatly appreciated. I’m under contract so I need to get back in the air.
Many Thanks in advance.
Mike
Email: [email protected]
“No Image Transmission”
For 3 weeks I have have tried every conceivable thing to remedy the problem but according to my hidden files (below) there is no communication on any of the 3 machines to the video transmit transmit board.
Everything else on the machines works perfect (except no image) it flies fine, Sats locks, IMU good, calibrates fine, etc.,etc. When I record video or stills, it records the data fine on the chip. When I stick the chip in my Mac, everything is normal good quality and clear playback. The second remote trans also works perfect.
This is just a "Few" of the different options I’ve tried:
Tried three different transmitters
Tried different locations
Changed 3 Batteries
Changed the micro chips
Re-installed the same firmware on machine
Install latest Firmware on machine
Re-Installed latest firmware on the transmitter
Re-installed the Go App
Tried 2 different iPad Mini’s
Try iPhone 6 +
Try a Samsung S7
Remove the camera and cleaned all the contacts
Try countless different combinations on the app i.e. 4K, 1080 decoding, etc.
I checked the hidden files on both the Inspire and P3P and it shows "Device Not Detected" on 08 00 & 15 00. which means the output boards are DOA.
[00006569]========== remo-con disconnect. boot(15) ============
[00006617]Packet [C:\WM610_FW_V01.10.01.40.bin] detected, card sn [0x07909b35].
[00006667]Packet upgrade start...
[00006715]Packet checking...
[00006772]Packet vlink 01.10.0140 <-> 01.09.0130.
[00006827]Record vlink 01.04.0010 <-> 01.03.0000 (flow = 0).
[00006882]Done.
[00006925]Version checking[1]...
[00006997][04 00][00] v1.30.1.43 -> v1.30.1.43
[00019567][08 00][00] device not detected.
[00019609][01 00][00] v2.70.5440 -> v2.70.5440
[00019654][01 01][00] v2.70.5440 -> v2.70.5440
[00019741][03 05][00] v34.1.0.5 -> v34.1.0.5
[00019819][03 06][00] v2.4.20.28 -> v2.4.20.28
[00019919][05 00][00] v3.0.6.2 -> v3.0.6.2
[00019995][09 00][00] v3.1.0.0 -> v3.1.0.0
[00020079][11 00][00] v3.9.0.0 -> v3.9.0.0
[00020167][12 00][00] v1.11.0.0 -> v1.11.0.0
[00020240][12 01][00] v1.11.0.0 -> v1.11.0.0
[00020319][12 02][00] v1.11.0.0 -> v1.11.0.0
[00020462][12 03][00] v1.11.0.0 -> v1.11.0.0
[00033007][15 00][00] device not detected.
[00033078][17 00][00] v1.1.0.8 -> v1.1.0.8
[00033180][17 01][00] v2.0.1.6 -> v2.0.1.6
[00033232][19 00][00] v1.0.8.96 -> v1.0.8.96
[00035277]Packet upgrade failed at version checking.
On the P3P - I ordered a replacement board for my P3P but the one DJI sent to me only has 2 antenna connections where mine as 4 connections. Would anyone have the correct info or board?
On the Inspire - I cannot find any information at all on the transmission board or its replacement.
It appears this No Image Transmission problem is very common and wide-spread. In the past month, I’ve found hundreds of posts with the same exact problem. I’m assuming the output board is running too hot and after a 6-12 months they all start failing.
I tried the DJI forum for 3 weeks now with absolutely no help or any solution, DJI is very aware of the problem but refuse to comment or assume any repair based on the fact they would have to replace thousands of boards and of course DJI does not have very much money (Only $10 Billion) to fix this problem.
Any help would be greatly appreciated. I’m under contract so I need to get back in the air.
Many Thanks in advance.
Mike
Email: [email protected]