i have a phantom3 advanced
I have been flying for 1 year now.
i upgraded the software many times. has some problems in the past, but not to this extend.
CLEARLY DJI DOES NOT TEST THE SOFTWARE BEFORE RELEASE
i recently got a notification that there is a update available for my drone
so i continued to update the RC and the drone.
Once the update finished, i got an error message "No Signal"
the drone and the RC lost signal. i got no camera view
the software tell me that it has full RC and HD signal
i get no camera vliew
###### Status of the RC ###############
# when switched on the link light is green
# full battery
#######################################
##### The software on my tablet #####
# sine i upgraded the software on my tablet, my tablet hang when i close the DJI APP.
# APP: 2.4.1
# Remote controller: 1.6.0
# Firmware: 1.8.80+
#
# The software on my tablet indicate to me that i have full RC and HD signal
that is if the software open up, 9 out of 10 times the software of my tablet hang.
DJI TEST YOUR SOFTWARE BEFORE ROLL OUT !!!!!!!
so now i have to reboot my tablet every time i close the software.
THIS NEVER HAPPENED WITH THE OLD SOFTWARE. !!!!!!!
###################################################################
##### The software on my drone #####################################
========== 2016.07.11 18:27:41 =====================
Packet: P3S_FW_V01.09.0060.bin
Result: Abort.
The firmware on the SD card is identical to or older than the current firmware on the aircraft.
========== 2016.07.11 18:51:04 =====================
Packet: P3S_FW_V01.03.0020.bin
Result: Abort.
The current firmware does not support downgrade. Use a different version of firmware to downgrade the target version.
========== 2016.07.11 18:57:05 =====================
Packet: P3S_FW_V01.09.0060.bin
Result: Abort.
The firmware on the SD card is identical to or older than the current firmware on the aircraft.
========== 2016.07.11 19:01:43 =====================
Packet: P3S_FW_V01.09.0060.bin
Result: Abort.
The firmware on the SD card is identical to or older than the current firmware on the aircraft.
####################################################################
################ Status of my Gimbal ###########################
# green flashing
###################################################
Where can i get the old software for the RC and the drone that was stable
I will never update my software on my drone again.
clearly DJI does not test the software before roll out, so this grounded me.
I have been flying for 1 year now.
i upgraded the software many times. has some problems in the past, but not to this extend.
CLEARLY DJI DOES NOT TEST THE SOFTWARE BEFORE RELEASE
i recently got a notification that there is a update available for my drone
so i continued to update the RC and the drone.
Once the update finished, i got an error message "No Signal"
the drone and the RC lost signal. i got no camera view
the software tell me that it has full RC and HD signal
i get no camera vliew
###### Status of the RC ###############
# when switched on the link light is green
# full battery
#######################################
##### The software on my tablet #####
# sine i upgraded the software on my tablet, my tablet hang when i close the DJI APP.
# APP: 2.4.1
# Remote controller: 1.6.0
# Firmware: 1.8.80+
#
# The software on my tablet indicate to me that i have full RC and HD signal
that is if the software open up, 9 out of 10 times the software of my tablet hang.
DJI TEST YOUR SOFTWARE BEFORE ROLL OUT !!!!!!!
so now i have to reboot my tablet every time i close the software.
THIS NEVER HAPPENED WITH THE OLD SOFTWARE. !!!!!!!
###################################################################
##### The software on my drone #####################################
========== 2016.07.11 18:27:41 =====================
Packet: P3S_FW_V01.09.0060.bin
Result: Abort.
The firmware on the SD card is identical to or older than the current firmware on the aircraft.
========== 2016.07.11 18:51:04 =====================
Packet: P3S_FW_V01.03.0020.bin
Result: Abort.
The current firmware does not support downgrade. Use a different version of firmware to downgrade the target version.
========== 2016.07.11 18:57:05 =====================
Packet: P3S_FW_V01.09.0060.bin
Result: Abort.
The firmware on the SD card is identical to or older than the current firmware on the aircraft.
========== 2016.07.11 19:01:43 =====================
Packet: P3S_FW_V01.09.0060.bin
Result: Abort.
The firmware on the SD card is identical to or older than the current firmware on the aircraft.
####################################################################
################ Status of my Gimbal ###########################
# green flashing
###################################################
Where can i get the old software for the RC and the drone that was stable
I will never update my software on my drone again.
clearly DJI does not test the software before roll out, so this grounded me.