First of all thank you to everyone who reveals complex technical information on the forum.
I have known how to cope with my failures in my drones over time leaning on you, because the DJI forum is a complete disgust.
Second, I apologize for my horrendous writing, since I am doing it in Spanish and using googe translate to bring it to English, since I thank you for your understanding, it does not bother me in the least having to copy and paste each answer to understand it.
To the case...
I have a Phantom 3 Standard gimbal controller board, with the module 07 problem not detected.
I clarify some points to help the wise in their diagnosis:
-The controller board does not link with any RC.
-Does not receive updates via SDCard, throws error immediately after starting, even forcing the update by holding down the link button before turning on the aircraft.
-It does not receive Downgrade from FW, I know the DeBug procedure and it does not solve my problem, it throws an error with a BEEEEEEEEEEP.
-I have no history of the reason for the failure.
It is likely that my limitation in English also limits finding the thread with the solution that surely I should not be the first, but I only found half threads, so I would appreciate if you could redirect me to some procedure already published by one of the teachers who already They went through the forum and still participate.
Attached is the log of the last update attempt :
[00274151]========== remo-con disconnect. boot(15) ============ (RC disconnected because it was a forced attempt)
[00274190]Packet [C:\P3C_FW_V01.09.0200.bin] detected, card sn [0xbc5b3ac7].
[00274230]Packet upgrade start...
[00274272]Packet checking...
[00274320]Packet vlink 01.09.0200 <-> 00.00.0000.
[00274363]Record vlink 01.09.0200 <-> 00.00.0000 (flow = 0).
[00274399]Done.
[00274441]Version checking[1]...
[00274497][04 00][00] v1.51.0.0 -> v1.51.0.0
[00274641][11 00][00] v1.8.0.0 -> v1.8.0.0
[00274781][11 01][00] v1.8.0.0 -> v2.0.0.33, firmware v1.8.0.0 not support.
[00274830][11 01][00] v1.8.0.0 -> v2.0.0.33
[00274866][01 00][00] v1.14.4920 -> v1.14.4920
[00274908][01 01][00] v1.14.4920 -> v1.14.4920
[00275039][03 05][00] v34.2.0.9 -> v34.2.0.9
[00275128][03 06][00] v2.4.20.50 -> v2.4.20.50
[00287666][07 00][00] device not detected.
[00287732][09 00][00] v0.1.1.1 -> v0.1.1.1
[00287825][12 00][00] v5.9.0.0 -> v5.9.0.0
[00287940][12 01][00] v5.9.0.0 -> v5.9.0.0
[00288059][12 02][00] v5.9.0.0 -> v5.9.0.0
[00288178][12 03][00] v5.9.0.0 -> v5.9.0.0
[00288219]Packet upgrade failed at version checking.
I have known how to cope with my failures in my drones over time leaning on you, because the DJI forum is a complete disgust.
Second, I apologize for my horrendous writing, since I am doing it in Spanish and using googe translate to bring it to English, since I thank you for your understanding, it does not bother me in the least having to copy and paste each answer to understand it.
To the case...
I have a Phantom 3 Standard gimbal controller board, with the module 07 problem not detected.
I clarify some points to help the wise in their diagnosis:
-The controller board does not link with any RC.
-Does not receive updates via SDCard, throws error immediately after starting, even forcing the update by holding down the link button before turning on the aircraft.
-It does not receive Downgrade from FW, I know the DeBug procedure and it does not solve my problem, it throws an error with a BEEEEEEEEEEP.
-I have no history of the reason for the failure.
It is likely that my limitation in English also limits finding the thread with the solution that surely I should not be the first, but I only found half threads, so I would appreciate if you could redirect me to some procedure already published by one of the teachers who already They went through the forum and still participate.
Attached is the log of the last update attempt :
[00274151]========== remo-con disconnect. boot(15) ============ (RC disconnected because it was a forced attempt)
[00274190]Packet [C:\P3C_FW_V01.09.0200.bin] detected, card sn [0xbc5b3ac7].
[00274230]Packet upgrade start...
[00274272]Packet checking...
[00274320]Packet vlink 01.09.0200 <-> 00.00.0000.
[00274363]Record vlink 01.09.0200 <-> 00.00.0000 (flow = 0).
[00274399]Done.
[00274441]Version checking[1]...
[00274497][04 00][00] v1.51.0.0 -> v1.51.0.0
[00274641][11 00][00] v1.8.0.0 -> v1.8.0.0
[00274781][11 01][00] v1.8.0.0 -> v2.0.0.33, firmware v1.8.0.0 not support.
[00274830][11 01][00] v1.8.0.0 -> v2.0.0.33
[00274866][01 00][00] v1.14.4920 -> v1.14.4920
[00274908][01 01][00] v1.14.4920 -> v1.14.4920
[00275039][03 05][00] v34.2.0.9 -> v34.2.0.9
[00275128][03 06][00] v2.4.20.50 -> v2.4.20.50
[00287666][07 00][00] device not detected.
[00287732][09 00][00] v0.1.1.1 -> v0.1.1.1
[00287825][12 00][00] v5.9.0.0 -> v5.9.0.0
[00287940][12 01][00] v5.9.0.0 -> v5.9.0.0
[00288059][12 02][00] v5.9.0.0 -> v5.9.0.0
[00288178][12 03][00] v5.9.0.0 -> v5.9.0.0
[00288219]Packet upgrade failed at version checking.