gimbal

Hi folks, Another issue with P3P. Not sure what really happened but now P3P gimbal is falling asleep after drone is turned on. It dances that starting loop then green light blinks few times and camera goes down like falling asleep. I know that GL300C RC is recently upgraded. Yesterday this P3P...

I tried to fly my P4P+ in 18miles/hour wind and to take some photos (short distance <500m, altitude <50m), I found the gimbal could not move at all. It kept in downward position. Then I took the drone home and re-calibrated the gimbal and IMU, everything was fine. I flied at home, gimbal showed...

is it possible to put yaw/roll/pitch motors into a gimbal assembly that are not native to the assembly? I believe the gimbal motors all get calibrated as one unit at the factory and replacing motors can throw this off. can anyone confirm? I was able to put a non native pitch motor onto a gimbal...

Hello everyone, I have done a lot of searching but have not find a solution for my problem. Story: I was out flying with my drone on the Maldives (quite hot weather), had three batteries with me. Flew my drone and empty two batteries. Placed the drone in the shadow for like 20 min. Started...

Hi, Probably someone already touched this topic (then please just give a link to it) - do you know where could I get some schematics for P3P gimbal? If there is anyone who has tried to re-solder components on gimbal board I would be pleased to chat. Cheers

Hi everyone, A novice here with a little Mavic Air experience and a past life in fixed wing and aerobatic helis Sorry to introduce myself with a plea for help, but it appears I have got myself into a world of hurt here. I bought a second hand P4 off a good mate. The full history of the drone...

Okay, so I had a pretty bad crash with my DJI Phantom 3 Standard. Gimbal plate broke, flex cable and 2.4Ghz antennas ripped right out of the gimbal and stripped the connectors off the end that connects to the logic board of the gimbal. The plastic connector on the gimbal logic board was ripped...

I've been having problems with my p4 for a while now. My gimbal started by "bouncing" during flight and sending me gimbal motor overloaded warnings. I did some research and decided to replace the yaw arm (because it was bent), the roll motor, and the gimbal ribbon cable. I did so and have seen...

I couldn't find this topic anywhere else, apologies if it's been covered. I'm a graduate student looking at modeling wild pig damage on crop fields using a newly acquired Phantom 3 Standard and Parrot Sequoia. I'd like top fly the Phantom without the standard gimbal camera attached, and have...

I needed My Gimbal and Camera Repaired But DJI say there's no Warranty, i had the Phantom 4 for 9 Months Dji Say There Warranty for the camera and gimbal is only 6 months . I wish i knew that i had the problem 2 months after i purchased the drone thinking i had a one year warranty..... Now I'm...

Hey guys, sorry if this is in the wrong place, I'm now. I recently got a phantom 3 standard without gimbal or controller that hasn't been activated yet. I picked up a used gimbal and a used controller and I'm having trouble connecting to the drone. I got my phone to connect to the controller...

$3500 USD Located in Los Angeles, CA DJI S900 Drone A2 Controller Lightbridge 2 + 2x Ground Units (on controller and another for client monitor) HDair MR 360 Gimbal + Handheld Adapters Futaba T14SG Controller + charger iCharger 306B + power source Pelican Case for travel 2x Tattu 16000...

I was running a mission with waypoints using Litch and when I finished I realized that the gimbal no longer responded to TX commands. The gimbal performs initialization movements when the drone is turned on and responds to the commands on programmed missions, it also responds to IPED movements...

Has anyone had to replace the vibration absorber that connects the gimbal to the aircraft frame? I sideswiped some tree foliage with my P4A, and it fell into bushes 50 ft. below that broke the fall. The props weren't broken, nor the landing gear, and no cracks show. It still flies okay and the...

My gimbal is completely gone; limp and no movement at all. Does anyone know where I get a gimbal spare part for a Phantom 4?

I accidenty flew my drone into some branches and it crashed into the ground. The gimbal broke along with the black flat wire but i see its repairable and i have been able to find the kit to replace it but i cant seem to find this one wire thats goldish and connects to this motor. Anyone know...

Had a crash and most of the wires disconnected. Need help in knowing which connectors to re-attach wires to. - There are two sets of 3-conductor black wires for the motors. One end is still attached to motor(s), just need to know which connectors on control board to attach them to. Then...

I crashed my Phantom 3 Standard last week. One wing snapped, but the case was mostly OK. Not so much for the gimbal. Video of gimbal issue: Whenever I turn on the unit, the gimbal sits slightly off centre and seems to be overloading. Diagnostics in the app are telling me everything's fine. I...

Hi, I bought a P34K with broken gimbal to try to fix it. When i bought it i knew that the roll motor and/or flat cable was defective. Flat cable is now replaced, but not motor. My main question here is: Should i get video feed even if the gimbal cannot calibrate at start and shuts of all...

I can see camera on my phone but the gimbal not moving.If I go on the setting to adjust manually calibrate it beeps the ribbon cable looks good. I think it may have been wricked but do not know.