Recent content by Wtneo

  1. W

    Aftermarket Batteries $95 USD

    bought 2 of these aftermarket batteries direct from China taobao - usd$72 each shipping included (shops locally in Singapore charges about usd$150) Got them today, plugged them in and glad to report that they are compatible with latest firmware, will report when I get a chance to use them.
  2. W

    Video: Fitted my Phantom v1 into a Phantom 2 shell (easy!)

    Re: Video: Fitted my Phantom v1 into a Phantom 2 shell (easy you will need a battery door to keep everything inside - there are a few on shapeway and reasonably priced. You will also need the new 9450 props to make use of the new esc/motors. My opinion is that the new esc and motors will...
  3. W

    DIY ND filter - 1g!

    just giving a head up on my DIY ND filter took one of those cheap plastic lens cover, dremel the center out. Cut out the ND4 film I bought from ebay and fixed it to the lens over! its only 1g!!
  4. W

    DJI Phantom 1 maximum battery

    the multistar 5200mah can fit - see the post below viewtopic.php?f=29&t=28392 you will need to remove the rails in the battery compartment, and use a carving pen to widen the opening of the battery bay. it does fit!!!
  5. W

    phantom - build from ground up

    nice work! ...should try on a brushless gimbal!
  6. W

    phantom - build from ground up

    A short clip of the flight No jello and fairly locked in - but probably will do better with some further tuning the alexmos pid settings http://youtu.be/J7e12rENj48 **edited. uploaded to youtube at a higher bitrate
  7. W

    phantom - build from ground up

    Took the maiden flight out today - some initial observations The sunnysky motors run very smooth, fairly similar to the original dji motors. The controls are ok with my gains setting, so far good for AP flight. The DYS smart gimbal with the gopro runs surprising well, got it cheap on the forum...
  8. W

    phantom - build from ground up

    I think the nylon ones will fit the sunnysky motors!
  9. W

    phantom - build from ground up

    gemfan does have the 9443 props that is compatible with the sunnysky motors - i am deciding if i should get them! ...the props came in today but didnt have time to fly the phantom today. realised the vibration from the motors were from poorly mount motors - they were nice and smooth after some...
  10. W

    phantom - build from ground up

    work in progress but i have managed to scavenge left over parts from a phantom 1.5 upgrade... basically reworked the old v1.1.1 shell to accommodate the multistar 5200mah battery, sunnysky 2212 980kv motors with afro ESCs, and the naza m lite as flight controller. As for the transmitter - i...
  11. W

    Video: Fitted my Phantom v1 into a Phantom 2 shell (easy!)

    Re: Video: Fitted my Phantom v1 into a Phantom 2 shell (easy thanks for the info!
  12. W

    Video: Fitted my Phantom v1 into a Phantom 2 shell (easy!)

    Re: Video: Fitted my Phantom v1 into a Phantom 2 shell (easy Quick question for those upgraded into p2 shell with h3-3d - i am using the new shell with the bigger hole at the bottom to accommodate the h3-3d. I have a new h3-3d coming in hopefully arriving this coming week, but would like to...
  13. W

    Looking for a good 3000 Mah battery

    the multistar 3000mah 3s lipo is a direct fit for the phantom i managed to fit the 4000mah version into p1 with some slight enlargement of the battery bay
  14. W

    Video: Fitted my Phantom v1 into a Phantom 2 shell (easy!)

    Re: Video: Fitted my Phantom v1 into a Phantom 2 shell (easy can you do a quick rundown/review of the the 450 sized phantom shell? I am seriously contemplating getting it!!! what are the size of the battery bay? how would you be hooding up the antenna?
  15. W

    NEW 2800mAh

    http://youtu.be/Xx06u0E1N1U It will barely fit without modification - will fit better if you can widen the door sightly with a carving knife