Recent content by WellyflyerNZ

  1. W

    P3A & Samsung Tab S 8.4 unusable. Help

    So I went out and purchased a Ipad mini 2. Video was so,so smooth compared to what I had seen on my Samsung android tablet. Hardware decode enabled. Only test flew for a few minutes so cannot comment on whether it overheated, or if any lag developed later on in the flight. Compared to my...
  2. W

    P3A & Samsung Tab S 8.4 unusable. Help

    Thanks. I will try this over the weekend.
  3. W

    Choppy video on the tablet?

    According to the pilot app my firmware is up to date. Seemed strange though as I have not updated it. I only received it yesterday, so maybe my supplier updated it already. I will look tomorrow and find what version I am on to be sure. Thanks
  4. W

    Phantom 3 pro FPV Glitch

    What device did you format? can you explain. i too am having video feed problems and looking for a solution. thanks
  5. W

    Choppy video on the tablet?

    I am having the same issue. with a samsung tab s 8.4. Although my video is VERY VERY choppy. Not useable as it is. will reply here too if i fond a solution.
  6. W

    P3A & Samsung Tab S 8.4 unusable. Help

    Hi, Yesterday my P3A arrived. I have since been out for two short distance park flights, at two different locations. Both areas with low congestion of wifi signals. I have the latest android App installed on my Samsung Tab S 8.4, and the latest P3A firmware on the quad. I know the tab S...
  7. W

    samsung tab s 8.4 perfomance?

    Hi, Can anyone tell me if the Samsung tab s 8.4 plays nice with the pilot app and the phantom 3? I have the tablet already, it worked great with the vision plus. I am hoping to have an experience as lag free as possible. Hopefully without having to buy another tablet. Still waiting on...
  8. W

    FPVLR Stage 3 - 2.4ghz Video issues - Need help

    I have had some sucess in solving this problem. I have not tested further out than about 800m so far. First i removed all stage 3 antenna from the phantom. I then Re-routed the cables, so the 2.4 pigtail was not crossing over the main board and reciever. Ended up wih the 2.4's on one side and...
  9. W

    Let's see some videos!

    Footage of the south coast of Wellington, New Zealand https://www.youtube.com/watch?v=2SlVJoRHa5M
  10. W

    FPVLR Stage 3 - 2.4ghz Video issues - Need help

    Hi Tony, I have had a look at the connectors inside the extender again this morning. From memory i didnt force them on, and they seem to look ok. Check the pics below. I downloaded Wifi analyzer onto my tablet and checked the signal of the two wifi networks. I made a alias within wifi...
  11. W

    FPVLR Stage 3 - 2.4ghz Video issues - Need help

    Hi, Over the past week i have finally got onto some long planned upgrades for my vision plus. aluminium foil gps mod. stage 3 fpvlr flytrex live 3g the flytrex and foil mod worked great. I am having some trouble and having really bad results with the 2.4ghz video connection. I am...
  12. W

    5.8 phantom receivers

    Hi. Sorry if this has been covered already. I cannot find the information after searching. Are the 5.8 receiver boards between the phantom 2 vision and the phantom 2 vision plus, interchangeable? I assumed they would be, and almost purchased the DJIPV-16 version from a local auction site...
  13. W

    Let's see some videos!

    First flight that wasnt at a park or school field. Shot at Island Bay, Wellington NZ. 720p 60 frames. Removed fish eye in after effects. adjusted contrast (maybe a bit too much!) Sorry, about the raw footage. https://www.youtube.com/watch?v=7wSlcSzsHFc I am going to try 1080 next time, or...
  14. W

    New Flytrex Goodies

    Hi FlynFrank. Thanks for your REALLY REALLY helpful answer. What an asset to this forum your are! These tests have been done in a house, in a car, in a wide open farm field, in a back yard, local school rugby pitch and even down by the sea. Regardless the result is always the same. This IS...
  15. W

    New Flytrex Goodies

    Hi, Today I managed to get my flytrex live to connect. It took about 10-15 tries but eventually it connected. I thought I would try upgrade the firmware to see if that would help with the issues I am having. So I went on-line to flytrex to set the device to upgrade. Once again I had to power...