Recent content by timtown

  1. T

    Charging / Discharging DJI Phantom Batteries

    Thank you, Phil. Not surprised about Dji. Consistent with their money sucking campagne. On the side, did you note their interview with a news commentator about the craft that landed on the White House lawn. The DJi Mouth, told everybody that they have taken measures to avoid high profile danger...
  2. T

    Charging / Discharging DJI Phantom Batteries

    Thank you msinger, I suppose this means I have to plug in each battery, and then, download firmware for the battery. I didn't realize the battery keeps time. Tim
  3. T

    Charging / Discharging DJI Phantom Batteries

    Hi all, I need suggestions for a smart charger that can handle Phantom 5200mAh 11.1v batteries. By handle, I mean to charge to max 11.1v and to discharge to 50% as recommended for storage. I have no clear understanding for the shelf life of these batteries and how they decrease output /...
  4. T

    Using Acetone on DJI shell

    As a correction to my previous post, DO NOT use Acetone on polypropylene. It will crack the surface. My shell simply broke apart after sitting in place for a while.
  5. T

    Screwing Around

    I would use the same color as painted around the end of the arms (motor mounts) to tie the colors together. A dark silver-grey might be another option. I would also get rid of the red decals and use white ones. Assuming the underside of the decals have been painted as well and you can't find...
  6. T

    What screws go where?

    Justin00: I need to put the whole thing together. Justin, if you could find the file, it may help. Msinger: Yes, I saw this video or one like it. The issue I have is with screw diameter and length. I have three sets of all screws. I know that you can blow it by using a long screw over a...
  7. T

    What screws go where?

    Hi forum members, Does anyone have a clue about where I can download a .PDF to show me what screw goes where in reassembling a Phantom V2+ shell? I have three shells to reassemble. Thanks
  8. T

    Using Acetone on DJI shell

    In my exasperating journey to paint my V2+, I've learned a few things that I wish to share. So far, I have purchased 3 clam shell replacements. In preparing my 1st top (I used the top of the original DJI V2+), I used rustoleum blue gloss and w/o explanation decided to apply a Krylon satin...
  9. T

    Screwing Around

    Re: Screwing Around - Paint Incompatibility About painting the Phantom, make absolutely sure the primer is compatible with the paint you desire to paint on top of it. For instance, Krylon is a lacquer and is incompatible with Rust-Oleum's UMA primer/sealer. I just made the mistake of...
  10. T

    Screwing Around

    Yes, I believe the body is the same as the P2V; same screws, same holes, same dimensions, etc. As I recall the cost is ~$67 plastic and all screws included (Amazon). I spray painted mine and then applied 3m vinyl. I strongly advise your use of white primer. Allow it to cure adequately. Then...
  11. T

    cracked plastic

    Speaking from experience, I would try everything before considering a new shell. See my post "Screwing Around". I have used "E6000" glue on my Phantom where I busted the plastic on the bottom half at the tip (I over tightened and a 1/4" chunk broke out). E6000 is like model airplane glue, but...
  12. T

    Screwing Around

    I have included bare-bones pictures of the Phantom quad minus electronics, motors, battery, camera/gimbal, and screws. Views include the clam shell intact, the inside and outside of the bottom of the two shells and the inside of the top clam shell. 74 screws hold these two clam components...
  13. T

    Got V3.0 Power?

    I have a basic question about upgrading the motors, etc. most certainly the power drain on the battery will increase. What is the assumption being made by you all wrt increase in lifting capacity, decrease in flight time, etc.? I don't know enough about battery technology to know that DJI can...
  14. T

    Adv. IMU cal and Sat Acquisition with Ext antenna

    Yes, but the coating on the aluminum (Dakota Wings as I recall) uses a good dielectric. I bought it primarily for its use as a template (I'm lazy). Regards, -Tim
  15. T

    Adv. IMU cal and Sat Acquisition with Ext antenna

    Hi forum members, I had startling success in GPS sat acquisition with mods implemented by other forum members! I also want to share advice given to me by a DJI engineer in L.A. with whom I discussed the d the message Phantom MC overheated message during the advanced calibration procedure...