Recent content by sethmad

  1. S

    Batteries dead and gone?

    if you open the battery and charge individual cells to 4V, you can revive the pack. If not, the BMS chip has locked the battery, you can reset the chip but you need some electronic skills and an EV2300 interface board. Disassembling lion batteries implies some risks. Do this only if you know...
  2. S

    ???Question About Phantom 3 LiPo Battery Balance Charging/Discharging???

    4 years later... i can confirm that the battery does not self balance. I have one pack and 1 cell is lower voltage than the others. After charging, 3 cells are at 4.35V and last Cell is 4.17V. For me this seems very strange, why does it not balance the cells? Do you know any way I could charge...
  3. S

    P3A Low Light Photo

    i have a plugin/extension installed in chrome (just search "EXIF reader chrome") Another way to do it: save the .jpg on your desktop and then right click and go to properties. You should see the exif info if you go to the details tab,
  4. S

    P3A Low Light Photo

    first is ISO 1037, second picture is ISO 110... you can see that in the exif
  5. S

    H3-3D problem on Phantom 1 v.1.1.1 with upgrade board (no external GCU)

    Can you write here the SW versions you have for NAZA-M, PCB330, GCU, etc (you can find this in the update tab in NAZA-M assitant.
  6. S

    Install onto P1 (P330D)

    I also did it with the upgrade board. Unfortunatelly I had problems with the lever controlling the gimbal tilt. It was working in progressive mode and not in follow mode. (the lever has to be in middle 0 position in order to stay fixed, otherway it will go all up or all down slowly. I only...
  7. S

    How to correct gimbal not parallel to the ground?

    there is a way to reset it (you connect some test points on the black PCB when you power it on) You can find the film on youtube.
  8. S

    H3-3D problem on Phantom 1 v.1.1.1 with upgrade board (no external GCU)

    I just did the Sarawuth Can bus mod (although the update board now has a 4 pin CAN bus connector). I mounted an iOSD mini and the GCU which came with the H3-3D. The tilt lever now works as expected (in follow mode). I wrote DJI, no answer, shitty company. Its probably the last drone i buy from...
  9. S

    Gopro fix

    lightroom CC. You can fix this in one click, it already recognizes the gopro camera.
  10. S

    H3-3D problem on Phantom 1 v.1.1.1 with upgrade board (no external GCU)

    The X1 channel is calibrated, I can see the lever moving in the assitant... but the gimbal is working in incremental mode. Unfortunatelly I dont know how to control/setup the GCU on the upgrade board...
  11. S

    P3P - bad pictures, interference patterns?

    looks like a sensor problem. return it for warranty.
  12. S

    Anyone perform the new NAZA UPDATE?

    Hello guys! I have the phantom 1 v1.1.1 and upgraded board (P330CB-H3-2D) I connected the H3-3D and it works... except that the X1 tilt lever is very difficult to use: it has to be on the 0 position in order for the gimbal to stay in a fix position. If it is at +/- 5 or so, it slowly goes in the...
  13. S

    H3-2D angle problem

    anyone tried to replace the H3-2D with a H3-3D on the phantom 1 with the upgraded board? The gimbal works but the lever only works in incremental mode. It should be at 0 position in order for the gimbal to stay fixed. If it is a little bit miscentered (+/- 5 on X1 channel in the NAZA assistant)...
  14. S

    H3-3D problem on Phantom 1 v.1.1.1 with upgrade board (no external GCU)

    Hello all, I've been reading through forums for days and couldn't find a solution yet. I have a Phantom 1 v1.1.1, on which I installed the upgrade board for h3-2d gimbal and then I mounted a H3-3D gimbal. The gimbal works but the gimbal lever that controls the pitch of the camera, works in...
  15. S

    H3-3D on Phantom 1. Is it possible?

    Hello all, I've been reading through forums for days and couldn't find a solution yet. I have a Phantom 1 v1.1.1, on which I installed the upgrade board for h3-2d gimbal and instead I mounted a H3-3D gimbal. The gimbal works but the gimbal lever that controls the pitch of the camera, works in...