Recent content by Quattro1

  1. Q

    Install the R6208 Futaba receiver on my Phantom

    I used sbus from R6208SB in into X2 on naza, then i used a conventional servo wire for channel 8. wired the antennas just like dji did, but instead of puting them both in the same direction outside the body, i taped one antenna along one of the legs, so they lineup 90* to each other. I attached...
  2. Q

    mixing sbus and conventional wireing(Futaba)

    strange :? you did follow this diagram? http://www.pyramidmodels.com/shop/shopimages/e-switch.jpg have you double checked your channel output? put a servo or something into that channel to see if its moving or not.
  3. Q

    Which receiver with Futaba 8FGA

    sounds like a good choice then :)
  4. Q

    Install the R6208 Futaba receiver on my Phantom

    Okay, futaba receiver is now instaled, the best reason to swap out the dji receiver is that you are not able to use more than 7 channels on the stock dji rx, and I'm actually using 8, 7 on sbus and one conventional.
  5. Q

    mixing sbus and conventional wireing(Futaba)

    I did also try to test my switch on the table like you, and it didnt work, but when I followed the included connection diagram, and actually soldered it to the BEC, everything works fine, so follow the connection diagram and and it will hopefully work :) I dont know if you going to put the...
  6. Q

    Which receiver with Futaba 8FGA

    No I dont se any good reason to use only conventional, but naza can handle 7 channels trough sbus, and if you like to use channel 8, you have to use conventional wiring for that channel. So the 2 extra outputs on R6303SB can be assigned to any channel?
  7. Q

    SOLVED! Bad GPS module???

    Re: Bad GPS module??? yeah it was a happy moment, it was a bit difficult to remove all the white glue, especially when the components are so close. A little patience and some good Tools was all i needed.
  8. Q

    HOW TO: balancing Vison props (using Top Flite)

    you are welcome.. but the props dosen't sit very firmly on the pin, due to the hard plastic on the senterholder, but it Works. You can easily drag a sticky tape againt the senterholder to improve it's holding capablilty.
  9. Q

    HOW TO: balancing Vison props (using Top Flite)

    many people wondering on how to balance vision props, here is how I did it using Top Flit magnetic balancer. This setup is completely without any modification at all, I have polished the magnets, but it's recomended anyway. this balancer generates a very low friction, and the propeller gets a...
  10. Q

    SOLVED! Bad GPS module???

    Re: Bad GPS module??? thank you I'll put that in mind, but I did figure out what was wrong, it was the grounding cable beween naza and gps module. DJI has put som glue on connections on the gps module, I removed it and mesured continuity on all 4 wires, and there was no connection on the...
  11. Q

    SOLVED! Bad GPS module???

    Hi.. I'm kind a flustrated now, last week I noticed my phantom wont go into GPS mode, I pluged it into the assistant software, and I noticed a message saying "GPS NEEDED" and the compas raw data is all saying 0 0 0. The GPS function is currently deactivated due to lack og GPS/compas input...
  12. Q

    mixing sbus and conventional wireing(Futaba)

    thank you guys, but how can you use more the 8 channels? do i have to sett the futaba RX in mode B(output 9-16)? (and run it together with sbus) or do I need to buy another RX and bind them both to my 8FGS to take advantage of channel 9-14?
  13. Q

    mixing sbus and conventional wireing(Futaba)

    anyone who have tried this??? have orderd 2 x TURNIGY RECEIVER CONTROLLED ON/OFF SWITCH, and I'll get them this week, gonna try it out then..
  14. Q

    Which receiver with Futaba 8FGA

    I recomend R6208SB, gives u the option of sbus and conventional wiring. :)
  15. Q

    mixing sbus and conventional wireing(Futaba)

    Hi. I'm using a futaba rx(R6208SB) in my phantom, and using sbus at the moment. naza can handle 7 channels, and I want to use the channel 8 for remoteswitch, so my question is; can I use output 8 on my rx and wire it conventional when I'm using sbus on output 1-7?