Recent content by pietpukje

  1. pietpukje

    SR6 replacement controller?

    Are you sure it is the controller? When you bind the new controller do the red light go out on the receiver board? It is not plug and play, you must bind the controller with the phantom.
  2. pietpukje

    P2V+ - can I replace original GPS by Ublox M8N ???

    Ceramic GPS Antenna 1575R-A Passive Antenna 1575.42MHZ 25 x 25 x 4 MM click on above text and you can make a gps booster self with several layers of tinfoil and tape.
  3. pietpukje

    P2V+ - can I replace original GPS by Ublox M8N ???

    try banggood for the antenna it cost €1,52 and free shipping to Holland so i expect it is the same for france. For the metalic cover, solder it back, its better
  4. pietpukje

    Phantom 3 Props

    if you get the wobble you need to go a little to the left\right\forward\back ( pick one ) and you get out of the vrs. i always do a little to the left\right\forward\back when coming down.
  5. pietpukje

    Left front engine or ESC problem

    Return after 4 months, no one accept that, only offical stores that give warranty. You can try the motors one by one in the naza assistent, do it without props. push realy quick the button during a few seconds and the motor must spin good and check of all the arms get hot or just one, are the...
  6. pietpukje

    GPS vs Atti vs Manual Mode

    Try the improve gps for vision , i used several layers of tinfoil between tape against short circuit and did not lose any satellites with filming after that back to ontopic: I always use gps mode
  7. pietpukje

    Repair service site

    Where are you from? If you hook the drone up to a pc, show the naza assistant a number or zeros behind gps
  8. pietpukje

    Multistar 4000mah alterative

    to Holland not, ordered a multistar 2 weeks ago, it was delivered in 3 days, no import dutys or tax
  9. pietpukje

    Multistar 4000mah alterative

    hobby king has then on stock in the eu warehouse
  10. pietpukje

    Please help... No gps just blinking yellow light

    And you can check if the gps board get power ( voltage ) put needles beside the wires and check with the voltmeter or there is power I got this result red - brown 5.50 volt red - yellow 1 2.47 volt red - yellow 2 2.35 volt yellow 1 - yellow 2...
  11. pietpukje

    Please help... No gps just blinking yellow light

    you can not check the board , only the wires. the only way to check the board is to connect it to another naza. if you realy want to check it your self then read this topic on rc groups there is some info and links on how the gps works. Naza v1/v2/Lite GPS module alternative (using APM 2.6...
  12. pietpukje

    Please help... No gps just blinking yellow light

    this is the gps print: the white stuff on the end of the wires is a sort kind of glue, you have to remove it carefully then you can use the multimeter to check the resistance of the wires the easy way is to put a wire in the connector and one pen from the multimeter to this wire and the other...
  13. pietpukje

    Please help... No gps just blinking yellow light

    i have unplugged the complete gps print on one of my phantoms and then i get a yellow flash every 3 seconds. so there is no communication between your gps print and naza.module. So it is not your compass causing this. You have to check the wires from the gps print to the naza for resistance with...
  14. pietpukje

    In neeed of some help, please. Much appreciated.

    red light inside is that the phantom is not connected to the remote controller. did you connect the cable from the receiver print good ( right port ,upside down) in the naza module? try to bind the phantom and the controller again. and did you use paint without lead in it? or else you get gps...
  15. pietpukje

    Please help... No gps just blinking yellow light

    multimeter --> the gps go to the naza module, not to the main board. the naza module is a red or yellow box borrowed this picture from another topic