Recent content by MickeM

Your spare fc-200 would be great! The white cable I have (FC-200 <-> Phantom) should work, but it is ugly, its stripped from insulation, A better one would be great. Yes, its the old style radio I got (was there two models with the Phantom 2 Vision?). I got the RE500 extender (RE700, isnt that...

That one was sold but I found two others for 150USD. What do you want for yours? I dont have any FC-200-camera. I helped a person with his other newer Phantoms and got mine for free, with some errors and without the camera. It works fine now (the one on the avatar), but the camera is the only...

I havent found anyone cheap... I really need one. Cheapest one I found was sold for 145USD. All the others are 299-600, and I dont need a new one, i need a good used one. :-) Its only the FC-200 I need, like this one http://ecx.images-amazon.com/images/I/41F4Oj0IbUL.jpg I have a gimbal...

Hi all! Is there any replacement camera for the FC-200 egg-looking camera to the Phantom 2 Vision? I have a brushless gimbal for the FC-200 and it also works with a GoPro. I never had the FC-200 (previous owner sold it since this Phantom was a spare part Phantom). It works with a GoPro, but...

It is not legal to send LiPo's by airmail, at least for most of the airlines. Its very expensive if they can. Sending a LiPo that has problems is even more risky. I will test one more time, then it will be discharged the saltwaterway and disposed.

The gimbal works fine, still dont have the cable for tilt. Anyone have the pinout for the white connector on the tilt-cable in the gimbal-end?

Havent had the time for this battery. But now I tried to charge it, nothing happens, all LEDs is off. Without charger: If I push the button once it lights upp two green LEDs. If I hold the button down for a few seconds to check the battery's life, all four green LEDs lights up. How do I drain...

Yes, all three cells shows the same voltage. Dont remember now, but they were like 4091 4094 4092mV. Ill discharge and charge it. Maybe its the Ri they measure?

In the Assistant: "One or more cells are damaged. Further use not recommended." Phantom: Blinks red (even when the battery was fully loaded). Pressing the button on the battery once: OK status on the battery Holding the button on the battery: All four LEDs lights up (over 90% life left). I have...

Thanks! I figured it out earlier. Works fine. I havent used a Phantom that much, but have flown several quads, some hexas and octa (Naza, ZeroTech, APM mostly). After learning the Naza-M Lite with GPS in my TBS Discovery, the Phantom were easy. All setups done and uses Naza-M-mode on the...

New receiver bought. One of the antenna were ripped out and had left the parts of the connector shorted on the receiver. Problem solved! =) Phantom is sold anyway.

I dont have the cable with the circuitboard on the end (that is on the photos above). :-) I only have an empty connector on the litte circuitboard: http://ecx.images-amazon.com/images/I/51gUqky9YvL.jpg Next to the two motor-cables, there is a white small connector. What is the pinout on that...

[SOLVED] Hello! The P2V+ have two dipole antennas for the 5.8GHz receiver. If one is cut in half in a crash. Can these be used: http://horizonfpvantennas.mybigcommerce.com/phantom-2-vision-new-connectors-uav-end-rc-control/ Im sceptic... GHz is sensitive. Is there any original...

I got this to work. =) I had to use the right version om SimpleBGC_GUI_2_2b2. First Windows-driver, then SimpleBGC. It is a 8-bit controller. I found it all here: http://www.basecamelectronics.com/downloads/8bit/ But... a new problem. There is a connector on the controller board. Using this...

Hi! I got this gimbal to my DJI Phantom 2 Vision: http://www.banggood.com/Refit-DJI-Phant ... 61974.html It works. But I want to adjust the parameters (because Im using a GoPro now). Drivers installed in Windows XP 32-bit. SimpleBGC GUI installed. Phantom-transmitter on. Phantom on. Gimbal...