Recent content by Malolo

  1. M

    9.5" props with the 9" prop guard?

    Thanks for the response rilot. When I measure the props I got with my p2 h3-3d, I am measuring from end to end with a ruler and the total length is 9.5 inches. As I type that out it makes me think, am I suppose to subtract the measurement of the hub? I guess what I really should be asking...
  2. M

    Red tinge on screen when motors start

    Thanks Jester but definitely not glare from the LED's! So I am still troubleshooting the situation with no luck. Here is what I have done so far: 1. Bypass the anti-interference boad - no luck 2. Bypass the iOSD unit - no luck 3. Remove all solder points and reconnect with bare wires and...
  3. M

    Red tinge on screen when motors start

    Howzit guys! So when I power on my p2, I get a perfectly clear screen and good color going to my black pearl. But when I start my motors, I get a red tinge on my screen. The tinge stays on during flight until the motors are shut off. I was thinking it was my vtx cables being too close to...
  4. M

    9.5" props with the 9" prop guard?

    Greetings! This might sound like a dumb question but am I supposed to use the 9" inch prop guards for my phantom 2 that has 9.5" props? Or do they actually make larger prop guards to be used with the larger propellers? Thanks! Malolo
  5. M

    Anyone know where else I can get this cable?

    Yup. There is the 32 channel RP-SMA version as well as a 7 channel SMA version. Supposedly the 7 channel SMA version is proven to work better with the immersion rc 600mw VTX and not so well with the 32 channel version. So if you plan on using the IRC VTX, I would suggest getting the 7 channel...
  6. M

    Anyone know where else I can get this cable?

    Sounds like you are going down the same road I (and many of the rest of us) went down not too long ago. What is best is probably debatable, but according to all the posts I have read, some components play more nicely together than others. I wanted to use an immersion RC 600mw VTX to save a...
  7. M

    plastic clips

    If you are just planning on flying your phantom without the gimbal, feel free to just break them and then replace them with some tie wraps but dont over tighten them. Anyone feel free to correct me if I am wrong, but I believe the securing pins are there just to prevent the gimbal from flying...
  8. M

    Honolulu, Hawaii (oahu)

    Howzit guys! I stay in honolulu so lmk if you guys like go fly or do some tandem aerial shots. Shoooooots! Malolo
  9. M

    3.04 Downgrade?

    Just confirming that as of today I was on 3.04 and was only able to successfully downgrade to 1.08. I tried the others but was not successful. Gonna take her out for a flight and see if I run into any issues. malolo
  10. M

    Best Controller for Phantom 2 - FrSky Taranis

    Thanks chipwich and khudson for the input! I went with what chipwich advised and it worked like a charm. Just had to go back into the dji assistant software to recalibrate and everything was all fine tuned. Thanks again everyone for the assistance, hopefully I'll be able to return the favor...
  11. M

    Best Controller for Phantom 2 - FrSky Taranis

    Thanks Chipwich and everyone else who contributed to this and the other taranis threads. I have been working along for the past 3 days to get my taranis up and running without using someone elses eeprom. After a day or so of frustration I had a moment of weakness and downloaded one of the...
  12. M

    IOSD Mark II - Switch Channels with Phantom Remote?

    Thank you ladykate for the insight. Would you mind letting me know what camera you use for FPV flying? I have looked online and seen a bunch of alternatives but am really looking for something that is small enough that I may mount just above the USB port or even dremel a hole and mount inside...
  13. M

    IOSD Mark II - Switch Channels with Phantom Remote?

    Thank you OIP for the response. What would you recommend as a replacement controller that would have 3 position switch that would allow me to control both the gimbal as well as to be able to switch/hop between the two video signals? Thanks!
  14. M

    IOSD Mark II - Switch Channels with Phantom Remote?

    Howzit everyone! Just got my P2 in yesterday and want to order an IOSD Mark II to switch between my hero3+ and some other smaller camera to use for flying. My question is, is it possible to use the stock phantom remote controller to switch between the two camera channels? or would I have to...