Recent content by Laid GP

  1. L

    Problem binding transmitter

    I had a little incident where I fried the Naza in my P1 and I recently replaced it with a brand new Naza M-Lite. Took it on its first flight and had a little crash, and had to re-solder some connections inside. The connector on the receiver module came loose, and when I reseated it I found I was...
  2. L

    Naza M-Lite

    I need to replace my Naza and everywhere I look seems to sell the Naza M Lite, which appears to be cosmetically the same as the Naza in my Phantom v1.2. Is it the same controller with just a different naming scheme?
  3. L

    Shorted something out w/gimbal pitch wire

    Yep look like I burnt the controller. Doesn't really have anything to do with the gimbal being cheap. Just me being stupid and experimenting with placing wires in different places :cry:
  4. L

    P2 compass and LED module on P1 Naza

    Is it possible to install the Phantom 2 compass/GPS module, and/or LED/USB module, on the Phantom 1 NAZA? My copter needs both parts and I thought I'd upgrade if possible.
  5. L

    Shorted something out w/gimbal pitch wire

    I was hooking up the pitch control on my gimbal (cheapo eBay Martinez gimbal) and I accidentally shorted the wires. Now my gimbal only has red LED lit (no flashing green) and I am getting a slow flashing red on the Phantom 1. The gimbal came with pretty much no instructions so I have no idea...
  6. L

    Phantom USB failure

    Any photos of your setup with the NAZA 2 led module? Is it just plug and play?
  7. L

    WTB: Phantom 1 LED board

    My LED board w/USB seems to have taken no dump and all the sites only seem to sell it in a package with the Motor Control board as well. Anyone have a spare laying around?
  8. L

    Yet another problem...

    Small update- after flying the light turns to a slow blinking yellow as if it is in ATTI mode.
  9. L

    Yet another problem...

    To recap, I had a bad crash, had to replace the ceramic antenna on GPS module and 2 motors. In the process of doing that I screwed up one end of the compass connector cable, and ordered a replacement for that. So now I have everything set up. But I have a couple problems that I am not sure...
  10. L

    GPS issues with Phantom

    Thank you so much! Just ordered one to fix the same issue with my Phantom.
  11. L

    Is my GPS module shot?

    So I am still repairing my Phantom 1 after a pretty severe crash. I have the motors replaced and everything seems to work. I went in to the Assistant software and I see that under the Upgrade section the GPS is listed as version 0.0.0.0. I can't set up IOC or any other settings related to GPS as...
  12. L

    Replaced motors, spinning in circles

    I swapped the red and black wires on those two motors and everything is hunky-dory now! I think my GPS module is dead though. It shows up version 0.0.0.0 in the assistant software and I get a blinking yellow light on the front of the Phantom. Seems to fly fine, though.
  13. L

    Replaced motors, spinning in circles

    Hello all, I replaced both of my clockwise motors and realized I couldn't get off the ground. I figured out that all 4 props are spinning the same direction. I think I reversed the wires, which two wires should I swap to get them going the right direction again?
  14. L

    Motor locked up, no light on that arm

    Charged the battery tonight and made my first successful test flight! Everything seems to be working fine! :D
  15. L

    Motor locked up, no light on that arm

    Got it all back together and tried flying, but couldn't get it off the ground. Then I got the flashing red light of low battery voltage so I've got the battery charger and will try again tomorrow. I assume the lack of lift is something to do with the low voltage. I connected using the Assistant...