Recent content by Graham Edwards

  1. G

    H3-3D - No Video to Black Pearl Monitor

    I bought the setup secondhand i think one antenna may be stock and the other one is a panel antenna. They have always worked before....but its a mystery. I think for me getting a picture when monitor is nearby rules out any fault with wiring on the drone. Its got to be a signal fault....im...
  2. G

    H3-3D - No Video to Black Pearl Monitor

    Ive replaced USB connector and ribbon. Yes i have a mini iOSD connected I am getting a picture with telemetry when monitor is near. But as soon as i move away theres no picture or telemetry on screen, its just snowy. Sent from my SM-N9005 using PhantomPilots mobile app
  3. G

    H3-3D - No Video to Black Pearl Monitor

    Its v3.00 the GoPro has not been updated. Sent from my SM-N9005 using PhantomPilots mobile app
  4. G

    H3-3D - No Video to Black Pearl Monitor

    Hi Jason yes it has correct antenna attached to it. [emoji106] Sent from my SM-N9005 using PhantomPilots mobile app
  5. G

    H3-3D - No Video to Black Pearl Monitor

    Well ive finally purchased another immersionrc TX and fitted it. Picture is a little clearer but still wont work unless i am near the drone, as in a couple of inches that is. just wondering could it be the Black Pearl Monitor starting to play up?. Its got to be a range thing if im getting a...
  6. G

    H3-3D - No Video to Black Pearl Monitor

    I will try another TX when i have time, thanks for the help.
  7. G

    H3-3D - No Video to Black Pearl Monitor

    The screen is snowy its only when you hold the drone near to the monitor that you can see a picture & the iOSD info, but the picture is still snowy. It worked fine before with the antennas im using. Both Monitor and Gopro are set to NTSC The red light is lit on the immersionrc but could it...
  8. G

    H3-3D - No Video to Black Pearl Monitor

    No never been powered up without antenna. Its an immersionrc / black pearl monitor and yes it has a mini iOSD installed.
  9. G

    H3-3D - No Video to Black Pearl Monitor

    Hi Jason, no still having problems with video. I am getting a picture but not very clear when i hold drone very close to monitor.
  10. G

    H3-3D - No Video to Black Pearl Monitor

    I ve opened the Phantom up to see if theres any loose wires inside....everything looks fine. I tried holding the drone near to the Black Pearl monitior and when it was close to the antennas on the monitor i got an intermmitant picture but was still snowy but got the colour back. So do you...
  11. G

    H3-3D - No Video to Black Pearl Monitor

    Just checked the firmware on GoPro 4 silver and its v3.00 so it should still be ok to use usb output.....unless someone on here has had trouble with that version?. Anyway think i am back to square one Is the yellow wire going to receiver the video out? would i be able too get a reading here to...
  12. G

    H3-3D - No Video to Black Pearl Monitor

    cheers bud......just read up on a few things to try could be along night!! :grinning:
  13. G

    H3-3D - No Video to Black Pearl Monitor

    The GoPro 4 has been working fine with the setup. I am not sure has it updated when transfering photos i will have to check.....can i rollback firmware if it has updated i wonder. It could be the cause if there is trouble with updates to GoPro.
  14. G

    H3-3D - No Video to Black Pearl Monitor

    Yes the red light is on.....and ive gone through all the channels and still no picture.
  15. G

    H3-3D - No Video to Black Pearl Monitor

    Thanks for the reply, yes it has a immersionrc 5.8ghz 600mw reciever and the antenna seems to be connected correctly. The reciever feels hot to touch im not sure if that is normal?...the switches on the reciever are set to 1&2 are off 3&4 are on. Cheers Graham