Recent content by FlyGuy07

what model gimbal is it? Does it have it's own software? What settings do you have under "Gimbal" in the NAZA software? My gimbal is a Beholder Lite and the pitch wire comes wrong out of the box, so I had to rewire it to make my tilt work. Whichever gimbal you have should (most likely) have...

I searched the forum and saw they someone already asked this but got no response... Does anyone have any recommendations for gain settings for antigravity motors (KV920) with antigravity CF 9x3 props? I just got mine all set up but was wondering if any settings needed changed. I have noticed it...

Re: Phantom 1.2.1 flying shaky after installing new MC/LED b well guys, it seems I've solved the issue with a little help from the advice in this thread. It turns out that my sticks (I'm assuming, because I only swapped them out) were the problem. I flew once the sticks were swapped out and my...

Re: Phantom 1.2.1 flying shaky after installing new MC/LED b If anyone would like to see my problem, here are two videos I uploaded to dropbox. One was mistakenly filmed vertically on my iPhone so you may need to tilt your head or open in VLC and rotate the video...

Re: Phantom 1.2.1 flying shaky after installing new MC/LED b Well, I finally got my Phantom back today after a 3 week wait and the note on the inside said they changed my ESC (as I had asked, because I accidentally bought red instead of green) and that they added shielding tape to my GPS. The...

Well, I just got an email from DJI and UPS saying the Phantom is shipping TODAY, literally one week after they told me the repair was complete. Needless to say I'm not too thrilled about this since I've been awaiting it ever since they told me the repairs were done. I emailed them back asking...

Do you remember if they shipped it out the same day they sent an email saying the repair work was done? They told me the repairs were done 6 days ago and I never got an email with tracking (checked everywhere) and it's still not here. Thanks

No it didn't cost me anything except shipping from me to them. I've only had it since October so it was under warranty. Basically it wasn't flying correctly and I tried everything to fix it to no avail. They even told me over the phone they had never heard of anything like it because my NAZA...

Hey guys, Does anyone know how long it usually takes for DJI shipping once they complete a repair? I got an email from them Tuesday saying they were done fixing my Phantom but not when I could expect it back. I replied and asked for a tracking number but never received one. Also, do they ship...

They told me repairs are running 2-3 weeks. If I were you I would have taken it to a hardware store and seen what they could do. They have drill bits that remove stripped screws. I'm sending mine out today for repairs too so I feel your pain.

It could be... my board wouldn't stabilize either so I mailed mine in last week and they're going to (hopefully) repair or replace it. They had me send it into the place it was originally bought from. It could be your Pitch and Roll PID numbers though. It's all pretty confusing but there are...

I've had a little luck with TeamRebelDesign via email, but I have the green board version... non Alexmos. You can try them at [email protected]

Re: Phantom 1.2.1 flying shaky after installing new MC/LED b Well I had thought it might be a motor issue so I ordered and installed T-Motor antigravity motors (which I wanted anyway) and then I flew again. Unfortunately after $190 motors and $75 in new MC/LED and receiver boards it's still...

Hello friends, Well let me start by saying this has not been my month when it comes to my Phantom. I bought and installed a Beholder Lite brushless gimbal for my Phantom and flew it and it worked great. I then opened it back up and got the tilt function set up and working. When I put the shell...

Re: Phantom 1 beeps and LED doesn't light up, Won't connect, Just an update guys, I've pretty much narrowed it down to the MC, so I ordered a new board. I also ordered a new receiver because the red light on it won't light up even with the NAZA powered (externally) and the remote off. I will...