Recent content by Crank

  1. Crank

    Phantom 2 back from a 3 year storage.

    I've been out of drone flying for about 3 years. I want to fly it again so I'm checking to see what are the latest and safest firmware updates. It looks like DJI isn't supporting P2 Drones anymore. Where can I go to get the firmware and information I need to launch again? Thanks Joe
  2. Crank

    Signature Picture?

    I didn't think about this before, but I think I know what the problem is. Sorry if I offended anyone.
  3. Crank

    Signature Picture?

    Is it possible to add a small picture in my signature? The statement "KEEP 'EM FLYING" was a old WWII saying and I have a picture I'd like to add.
  4. Crank

    Stuck in Warmup Mode.

    Runs good now. I checked the assistant NAZA program and could see the one of the 4 channels (E) was reversed. All others were normal. I put everything back to normal and ran IMU cal again. Looks like all is happy. I'll calibrate the compass before the test flight.
  5. Crank

    Stuck in Warmup Mode.

    I think I need to go thru all of my notes and see what one is the culprit. Thanks for the help.
  6. Crank

    Stuck in Warmup Mode.

    Yep. I do remember the IMU being too warm error. I think I will redo that just for kicks and grins. What's up with the IMU ERROR deal? I've seen that before.
  7. Crank

    Stuck in Warmup Mode.

    Just finished running calibration on the P2. After that I powered it back up and it started with the red-green-yellow flashing. I waited about a minute and it was still flashing that code. I don't know what wrong with it. I will try running the software again. I can't seem to find anything about...
  8. Crank

    Mini-iOSD Problem!

    I've been working on my Mini-iOSD problem for the last 3 days. I have a P2 Ver. 1.0, Black Pearl monitor, 600mw transmitter. I get a blank screen. No video or OSD info. If I run the camera video direct to the transmitter, I see video. I replaced the video in/out cable to the Mini-iOSD. No dice...
  9. Crank

    Zenmuse H3-3D-3D Gimbal and SJ4000 Camera Hassles.

    I moved this question from the Help forum to here. Is there anyone out there that has a SJ4000 camera on a Zenmuse H3-3D gimbal? There are two problems I see so far. I haven't gotten to the video yet. 1. The camera is slightly bigger than the camera mounting place. I'm talking total 1/64...
  10. Crank

    Need Help with the Receiver.

    Ok. Now I understand. Thanks. Sorry guys... This is all new to me. :D In time... In time.
  11. Crank

    Need Help with the Receiver.

    Let me get this straight in my head... One channel for all three axis. Pitch, Tilt, Yaw?
  12. Crank

    Need Help with the Receiver.

    Thanks for your reply. I'm running a H3-3D gimbal. Doesn't' that take up channels 7,8,9????? Does the 3 axis of the gimbal use just channel 7? That would be great!
  13. Crank

    So disappointed. Please help.

    DITTO. Sorry to hear about the problem. I'm guessing at this... With power off, can you spin the motors by hand. Spin it slowly and listen to the difference between the good and bad motor. Are the motor mounting screws up in too far? Are they rubbing? I think if you smell smoke, it's pretty...
  14. Crank

    Need Help with the Receiver.

    Helifreaks is also a place that has a huge following if No one here has experience with this setup... Serious!? Sorry, I thought this was a big thing here. My bad.... I'll give that a shot also. Thanks. Not saying you won't find someone with the answer here... Just trying to get you a few...