Recent content by chluk2425

  1. chluk2425

    Vision+ WiFi Booster Apps Compared

    15dBm, 200m high, 350 distance, 640x480 30fps, previously 70m high 300m distance 320x240 15fps, connection broken
  2. chluk2425

    Vision+ WiFi Booster Apps Compared

    Noted this post previously; but if a free app could do the job maybe it's better to stick with it... getting it wrong on a company's asset doesn't feel good to me... tough my boss has always encouraging me to mod it to get a longer range :? :?
  3. chluk2425

    Vision+ WiFi Booster Apps Compared

    so it's a one off, thanks clarifying :D
  4. chluk2425

    New member looking to get more range

    so that means there will have effect on it... :| argh, hate living in such humid area... but is that lost of power that huge... I know there's no rule of thumb for it, so much factor affecting each other.. maybe i really should try the coke can disk method... :?
  5. chluk2425

    Vision+ WiFi Booster Apps Compared

    ops... bad English :oops: howcome I remember seeing someone said the default was 7dBm for the drone and 12dBm for the repeater... ok, my bad not reading the spec sheet carefully.. I actually have a thought on the order of applying the boost... maybe it applies to android only as iphone will...
  6. chluk2425

    New member looking to get more range

    I will just tag along as I am looking for similar solution if the original poster won't mind, im not trying to hijack his post. May I ask will humidity affect the range on the 5.8 or 2.4 transmitter signal? I was googling about this and some said it will have effect, tough not much, by about...
  7. chluk2425

    Vision+ WiFi Booster Apps Compared

    may I ask what's your procedure or activating the booster? I was working in this order:- Turn on the reaper Turn on phone's wifi and connect the reaper Open booster apps Slide the button to on Set the values to 13dbm for both reaper and the drone Open up vision app and fly The results was, I...
  8. chluk2425

    Advance IMU Calibration

    Thanks for your kind help and clarification. But umm... Why exacto knife to slit the sticker? [emoji47] Unfortunately.... I screwed up two screws last time when I was trying to open the case... it's now stuck and cannot be opened... Also, I wasn't recording when I found this fluctuations of...
  9. chluk2425

    Advance IMU Calibration

    I finally have my drone successfully pass the IMU Advance Calibration... not sure why it works this time but not yesterday, only could think of I calibrate straight after i power it on so maybe it's really the heat issue.... may i ask, will the IMU help with the stability of the drone under...
  10. chluk2425

    Advance IMU Calibration

    May I ask, are you in phantom or NAZA mode?
  11. chluk2425

    Advance IMU Calibration

    I have just tried it outside, and it seems all good. The drone did not stay where i start but i think that's due to i have only 5 GPS (don't understand this, i am in a very very open area and still i am only getting 5...), occasionally when i get more than 5 GPS fix, it stabilize itself fairly...
  12. chluk2425

    Advance IMU Calibration

    My advanced Cali was neither never greyed out nor the text read calibrating... that makes me don't know whether it has finished or not.... Anything to do with Phantom mode or NAZA mode? It seems me and him got the same problem under NAZA mode.... http://www.phantompilots.com/viewtopic.php?t=17314
  13. chluk2425

    Upgrade to 3.04 now IMU won't calibrate

    does the basic cal & check IMU status back on when you switch to Phantom mode? I notice this when I switch back to Phantom as well, while in NAZA it's grey. but i didn't do advance calibrate again in Phantom mode since the checks said i am fine... and i just did a basic cali...
  14. chluk2425

    Advance IMU Calibration

    OK, I can't wait for it and stopped the calibration after half an hour, thinking to insert another battery as the one inside starts to go below 40%... i replace it, turn it on, no warning leds, then when i plug the usb in and fire up the assistant software, no error! It seems it has finished...
  15. chluk2425

    Advance IMU Calibration

    It hasn't stop changing since I started calibrating it... I can't put it on the ground as it seems the reinforcement in slab will affect it, at least it will affect the compass calibration..... Whig should I do if it stuck for so long....