Recent content by Builder2961

  1. Builder2961

    Good to see a fellow Ham enjoying this hobby as well. Best regards, Vin KD1GA

    Good to see a fellow Ham enjoying this hobby as well. Best regards, Vin KD1GA
  2. Builder2961

    Is your P4 firmware update GOOD? Post here please!

    Glad you got it connected. Good info, I haven't used the first screen option in a log time. I always take it to the flight screen then tap on status and update from there.
  3. Builder2961

    Is your P4 firmware update GOOD? Post here please!

    The remote needs to take the update. Make sure you shut off aircraft. Restart app and remote make sure you have a good internet connection. You should see a prompt on the app to up the RC.
  4. Builder2961

    P4 Step By Step Successful Firmware Update Procedure

    This procedure worked perfectly for me hope it does for you. I completed upgrade successfully and with all new flight modes enabled and Horizon tilt issues corrected. Using firmware v02.00.0106 IOS and Ipad 2 Air. Only issue like most, is I get erroneous high wind warnings even in light air...
  5. Builder2961

    Is your P4 firmware update GOOD? Post here please!

    Mine went fine. Horizon tilt fixed and new functions are all working.Flight was a bit more sensitive but that was handled with some sensitivity adjustments. Only issue I'm noticing is high wind warning all the time, even in calm wind.
  6. Builder2961

    Motor Rotation

    thanks for the good information. I'll have the shell off it this weekend (first time I ever popped the top on a P-4) and I'll post some pictures.
  7. Builder2961

    Motor Rotation

    Sure they do DJI Phantom 4 2312S Motor (CW) Single Unit (Part 24) DJI Phantom 4 2312S Motor (CCW) Single Unit (Part 23)
  8. Builder2961

    Motor Rotation

    Procuring the motors is not the issue. Identifying them is.
  9. Builder2961

    Motor Rotation

    Thanks for the reply. I have to disagree however. Quad Copters can fly and manuvor because the motors rotate either CW or CCW. On threaded prop mounts they have the thread the shaft opposite of the rotation or centrifugal force would spin them off. I have replaced a bunch of motors on my 3 and...
  10. Builder2961

    Motor Rotation

    The p4 motors don't appear to have a model number on them indicating CW or CCW unlike the p3 advanced. Have to replace a siezed motor. Any idea how to identify?
  11. Builder2961

    Antenna Pinouts and Compass Problem

    Update. Well the pin-out information provided above is correct. Aircraft receiving fine now. However still had compass problem. I'm not sure what the problem was with the compass but purchased a replacement and all is well. I must have damaged the connector or cable during the new shell install...
  12. Builder2961

    Antenna Pinouts and Compass Problem

    Ok well the pinout problem has been solved. I ended up removing the antennas from each leg and sure enough each antenna was labeled 1 thru 4. So now I can at least insure the antenna configuration matches the corresponding connector on the board. Reconnecting now correctly. I'll let you all know...
  13. Builder2961

    Antenna Pinouts and Compass Problem

    Knowing a bit about RF being a ham for 30 years, as I think about it, the aircraft doesn't just recieve it also transmits. So it may do both from each pin; I'm wondering now if two may be transmit and two receive. Guess I'll call DJI and see if they can shed some light on this. Thanks again for...
  14. Builder2961

    Antenna Pinouts and Compass Problem

    Thank you for the input. I have checked the compass cable, board and connector all looks good but that means nothing. I ordered a new compass and cable see what that does. I've owned a phantom 4 for months, so haven't kept up with 3 series at all. Tried to use DJI assistant on the 3, so I'm...